MOTIP - Chrome effect spray

Full specifications

MOTIP - Chrome effect spray

High-gloss effect spray that gives flat surfaces a shiny effect. It is suitable for use on metal, wood, glass and various plastics. Limited weather and smear resistance.

QUALITY AND PROPERTIES

• High-quality acrylic
• Good coverage
• Brilliant shine
• Excellent adhesion
• Fast drying time
• Good flow, flat surface
• Not weather or smear resistant!

PHYSICAL AND CHEMICAL DATA

• Basis of the binder: Acrylate
• Colour: chrome
• Smell: solvent
• Degree of gloss (at measurement angle 60° acc. to DIN 67530):
  not measurable, >100
• Efficiency:
  Depending on consistence and colour of the ground:
  400 ml are sufficient for approx. 1.25 m²-1.75 m²

• Drying time (at 20°C, 50% relative air humidity):

  Dust-dry: after approx. 10 minutes
  

  Cured: after approx. 24 hours
  The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.

• Temperature-resistant: up to 110°C
• Storage stability:
  10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
• Size:
  aerosol can, maximum nominal volume 400 ml

INSTRUCTION MANUEL

Before use, carefully read and observe the warning texts on the label!

Application:

• The surface should be clean, dry and free of rust and grease.
• First sand old paintwork and coated parts, then prime and, once dry, sand smooth with 600-grit sandpaper.
• Pre-treat highly absorbent surfaces with MoTip primer.
• Shake the can well for 2 minutes before use.
• Test spray.
• Keep a spraying distance of ca. 25-30 cm.
• Spray several thin coats at intervals of 2 minutes.
• Important: It is not technically possible to maintain the brilliant shine over the long term. Covering it with clear varnish will dissolve the effect coat. The shine can be renewed by re-spraying the surface when it has faded.
• Do not spray onto surfaces coated in synthetic resin.

 

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

---

WARNING:

GHS02 - flame	GHS07 - Eye Irrit

• H222 - Extremely flammable aerosol.

• H229 - Pressurised container: May burst if heated.

• H319 - Causes serious eye irritation.

• H335 - May cause respiratory irritation

• H336 - May cause drowsiness or dizziness.

• H412 - Harmful to aquatic life with long lasting effects.

• P101 - If medical advice is needed, have product container or label at hand.

• P102 - Keep out of reach of children.

• P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

• P211 - Do not spray on an open flame or other ignition source.

• P251 - Do not pierce or burn, even after use.

• P260 - Do not breathe spray.

• P410+P412 - Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

• P501 - Dispose of contents / container in accordance with regional regulations.

• EUH066 - Repeated exposure may cause skin dryness or cracking.Buildup of explosive mixtures possible without sufficient ventilation.

For download

Safety data sheet

Sicherheitsdatenblatt